Control Gears

DALI PS

DALI PS is the power supply for the DALI bus system. It delivers up to 250 mA, supplying the entire DALI bus installation. It can be used to power up to 64 addressable subscribers each with 2mA and additional 20 to 30 control modules ( DALI GC, SC, MC...) without a bus address.
Suitable for DIN rail mounting. Available in various housings.

DALI PS

DALI RM

The DALI RM provides a relay-switch controllable via the DALI bus, which can be used to switch luminaires and small loads or electro-magnetic actuators.
Loads without DALI input are thus integrated into the DALI system.

DALI RM

DALI RM8 / DALI RM16

The DALI RM8/16 provides a relay-switch controllable via the DALI bus, which allows to directly switch permant loads up to 2kW, the RM16 type supports inrush currents up to 160A.
A special feature is offered by the bistable relay, which holds the output state even in the case of DALI line supply outage.
Loads without DALI-input are thus integrated into the DALI system.

DALI RM8 / DALI RM16

DALI 4Ch RC DT7

DALI Relay control modul for 4 channels. One DALI-address per channel. Suitable for relays and circuit breakers with coil-voltages from 12V to 48V DC.

Types for remote ceiling and din rail mounting available.

DALI 4Ch RC DT7

DALI Jalousie

The DALI Jalousie can be used to control blind motors with   230V~ control inputs via DALI.  With the help of four configurable profiles the module can be adapted to any blind (e.g. changing the tilt angle and  open/close the blind).

Types for remote ceiling and for dinrail mounting available.

DALI Jalousie

DALI PD

The DALI PD is a phase-angle control module with DALI input for switching and dimming of luminaires. For example, 230 V LED lamps with Edison socket can also be integrated in the DALI system. Suitable for dimmable LED lamps up to 25 W.

Type for 300W available. Up from FW 3.5 additional operating mode as dali controlled switch supported.

Lunatone DALI phase dimmer leading trailing edge retrofit LED

DALI CW-WW CV DT8

LED Control Gear (CV) with 2 channels for the control of tunable white luminaires via one DALI-address (DT8).

As alternative to the DT8 control the operating modes Balance&Dim and Dim2Warm are available. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 28V DC or 12V to 48V DC, input current depending on device type (max 16A), 2 PWM outputs (16Bit)

DALI CW-WW CV DT8

DALI CW-WW CC DT8

LED Control Gear (CC) with 2 channels for the control of tunable white luminaires via one DALI-address (DT8).

As alternative to the DT8 control the operating modes Balance&Dim and Dim2Warm are available. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, output voltage range from 3V to 45V, types with constant currents up to  1000mA/channel (common plus connector) or 1400mA/channel (common minus connector).

DALI CW-WW CC DT8

DALI RGB CV DT8

LED Control Gear (CV) with 3 channels for the control of RGB-luminaires via one DALI-address (DT8).

As alternative to the DT8 control the operating mode Colour&Dim is available. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, input current depending on device type (max 16A), 3 PWM outputs (16Bit)

DALI RGB CV DT8

DALI RGB CC DT8

LED Control Gear (CC) with 3 channels for the control of RGB-luminaires via one DALI-address (DT8).

As alternative to the DT8 control the operating mode Colour&Dim is available. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, output voltage range from 3V to 45V, types with constant currents up to 700mA/channel with common plus connector or common minus connector.

DALI RGB CC DT8

DALI RGBW CV DT8

LED Control Gear (CV) with 4 channels for the control of RGB- or RGBW-luminaires via one DALI-address (DT8).

As alternative to the DT8 control the operating mode Colour&Dim is available. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, input current depending on device type (max 16A), 4 PWM outputs (16Bit).

DALI RGBW CV DT8

DALI RGBW CC DT8

LED Control Gear (CC) with 4 channels for the control of RGB- or RGBW-luminaires via one DALI-address (DT8).

As alternative to the DT8 control the operating mode Colour&Dim is available. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, output voltage range from 3V to 45V, types with constant currents up to 700mA/channel with common plus connector or common minus connector.

DALI RGBW CC DT8

DALI 1Ch-LED-Dimmer CV DT6

LED Control Gear (CV) with 1 channel. Controllable via  DALI or Sw&Dim/SwitchDim2.

Input voltage from 1V to 28V DC or 12V to 48V DC, input current depending on device type (max 16A), 1 PWM output (16Bit).

DALI 1Ch-LED-Dimmer CV DT6

DALI 1Ch-LED-Dimmer CC DT6

LED-Control Gear (CC) with one channel. Output signal can be controlled via DALI or SwitchDim.
Input voltage from 12V to 48V DC, types with output current of 350mA and 700mA available (other output currents available upon request)

DALI 1Ch-LED-Dimmer CC DT6

DALI 2Ch-LED-Dimmer CV DT6

LED Control Gear (CV) with 2 independent channels. Each channel has an own DALI-address.

Operating modes Balance&Dim and Dim2Warm for the control of tunable-white luminaires. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, input current depending on device type (max 16A), 2 PWM outputs (16Bit)

DALI 2Ch-LED-Dimmer CV DT6

DALI 2Ch-LED-Dimmer CC DT6

LED Control Gear (CC) with 2 independent channels. Each channel has an own DALI-address.

Operating modes Balance&Dim and Dim2Warm for the control of tunable-white luminaires. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, output voltage range from 3V to 45V, types with constant currents up to  1000mA/channel (common plus connector) or 1400mA/channel (common minus connector).

DALI 2Ch-LED-Dimmer CC DT6

DALI 3Ch-LED-Dimmer CV DT6

LED Control Gear (CV) with 3 independent channels. Each channel has an own DALI address.

Operating mode Colour&Dim for the control of RGB-luminaires. SwitchDim2:  control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, input current depending on device type (max 16A), 3 PWM outputs (16 Bit)

DALI 3Ch-LED-Dimmer CV DT6

DALI 3Ch-LED-Dimmer CC DT6

LED Control Gear (CC) with 3 independent channels. Each channel has an own DALI-address.

Operating mode Colour&Dim for the control of RGB-luminaires. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, output voltage range from 3V to 45V, types with constant currents up to 500mA/channel (common plus connector) or 700mA/channel (common minus connector).

 

 

DALI 3Ch-LED-Dimmer CC DT6

DALI 4Ch-LED-Dimmer CV DT6

LED Control Gear (CV) with 4 independent channels. Each channel has an own DALI-address.

Operating mode Colour&Dim for the control of RGB- and RGBW-luminaires. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, input current depending on device type (max 16A), 4 PWM outputs (16 Bit)

 

 

DALI 4Ch-LED-Dimmer CV DT6

DALI 4Ch-LED-Dimmer CC DT6

LED Control Gear (CC) with 4 independent channels. Each channel has an own DALI-address.

Operating mode Colour&Dim for the control of RGB- and RGBW-luminaires. SwitchDim2: control via 2 switch inputs without DALI.

Input voltage from 12V to 48V DC, output voltage range from 3V to 45V, types with constant currents up to 500mA/channel (common plus connector) or 700mA/channel (common minus connector).

 

DALI 4Ch-LED-Dimmer CC DT6

DALI LED Power Supply 15W/20W/25W

DALI LED-Dimmer with input for mains voltage (230V).

Types with constant current (350mA/500mA/700mA)  and constant voltage (24V, 1A max.) available.

 

DALI LED Power Supply 15W/20W/25W

DALI Repeater

The DALI repeater is used to amplify the DALI signal. This module extends a DALI line from the usual maximum length of 300 m to up to 600 m. The repeater is powered directly via the DALI bus.
Suitable for DIN rail mounting.

Type with integrated DALI power supply (200mA) available.

DALI Repeater

DALI Expander

The DALI Expander enables the control of multiple DALI devices using one DALI-address. Multiple devices form one DALI subgroup, which is controlled with the address of the DALI Expander (Broadcast). The device has got an integrated DALI bus supply (200mA) for the DALI subgroup. The amount of  ECGs can be increased as well as the line length (up to 300m).

DALI Expander

DALI Expander 3

Simple DALI-line expansion with 3 DALI subnets. Integrated 50mA bus power supply for each DALI subnet. The DALI-lines are represented by DALI-addresses in the main circuit (commands sent to the DALI-addresses are forwarded broadcast to the corresponding subnet). Alternatively the DALI subnets can be contolled directly by Switch&Dim inputs.

DALI Expander 3

1Ch-LED Booster/Dimmer

LED-Control Gear (CV) with one channel. Can be operated as PWM-Booster or Dimmer.
The device operates as PWM-Booster, if PWM-signals are being sent (50Hz-1kHz). The PWM-signal is given directly at the output.
The Dimmer can be operated with  100kohm-potentiometer or even other 0-10V control devices (active and passive).
Supply voltage: 12V-48V DC; max. connected current 16A, 1PWM output (16Bit).

1Ch-LED Booster/Dimmer